AC Amp Meter and AC Volt Meter are important when it comes to measuring electrical performance in industrial and commercial installations. These instruments are expected to give precise measurements of current and voltage, thereby ensuring a smooth running and safe electrical system. At Powertrac India, the core area is to provide a combination of durability and consistency in performance of precision engineered analogue panel meters.
The AC Amp Meters and the Volt Meters are commonly employed in industries because of their flexibility and dependability. They are normally mounted in:
Their main purpose is to assist operators to monitor the voltage and current levels to avoid overloads and ensure efficiency of the system. These meters in most instances serve as the initial monitoring meters before an advanced automation system sets in.
Among the most remarkable characteristics of these meters is their sturdy analogue design that provides a stable operation even under unstable power conditions. Polycarbonate casing ensures that internal components are not affected by dust, heat, and mechanical impact and, therefore, it may be used in industries where there is strong industrial impact. Slide-in scale structure provides it with a flexible design that can be customized easily depending on the range of measurements. Also, the meters can be panel mounted, so there is a clean and tidy installation without consuming excessive space. The other advantage is that they are low maintenance. They are not dependant on intricate circuitry, thus are more resistant to failure and can be used years with little or no maintenance.
The selection of an appropriate meter may greatly influence the functioning and the safety of your electrical system. Analog Amp volt Meter of Panel is unique due to its simplicity, accuracy, and reliability.
Contrary to digital meters, the analogue meters offer immediate visual feedback in the form of movement of the needle, which aids in the rapid detection of variations. They are also affordable and hence a viable option when using large scale installations.
These meters are produced in Powertrac India with emphasis on quality and precision, where each meter is of industrial standard. They are easily installed, constructed, and dependable which makes them a favorite among the engineers and technicians.
When you are in need of a good and effective means of checking the electrical parameters, then the Analog Amp volt Meter for Panel is a clever and reliable tool that can be used in any panel based application.
| Feature | Value |
|---|---|
| Electrical Specifications | |
| Type | Moving Coil Slide in scales. |
| Operating Voltage | 50 mV to 600V. |
| Operating Current | 100A to 30A & above 30A external CT |
| Accuracy | Class 1.5%. |
| Insulation Resistance | Greater than 20M at 500V DC. |
| Dielectric test | 2kV for RMS for 1 min. |
| Overload continuous | 1.2 times. |
| Overload short time | 2 times V /10 times l for 5 seconds. |
| Operating Temp. | -10⁰C to 55⁰C. |
| Storage Temp. | -20⁰C to 70⁰C. |
| Humidity | up to 95% RH |
| Conforms to | I.S. 1248/I.E.C. 60051 (Part 2) |
| Ambient temperature | 23 C + 2 C |
| Position of use | Nominal position + 1 |
| Input Waveform | Rated value of measured quantity sine wave, distortion factor <= 5% |
| Frequency | 45...65HZ |
| Other Conditions | IS : 1248 (IEC 51/ DIN EN 60051) |
| Environmental Conditions | |
| Climatic suitability | Climate category II as per IS : 1248 IEC 60051 (climatic class 3 according) to VDE/VDI 3540) |
| Shock resistance | 15gn for pulse duration 11 ms |
| Vibration resistance | 10-55-10Hz for ampli. 0.15mm (1.5g at 50Hz) |
| Pollution degree | 2 |
| Measured quantity | AC voltage or current |
| Power consumption (Approx) | |
| Voltmeters | < 4.5VA |
| Ammeters | < 0.5VA |
| Overload capacity (acc to IS : 1248/IEC 51) | |
| Continuously | 1.2 times rated voltage/current |
| Short duration | |
| Voltmeters | 2 times for 0.5 sec : 9 overloads 2 times for 5 sec : 1 overloads |
| Ammeters : | 10 times for 0.5 sec : 9 overloads 10 times for 5 sec : 1 overloads |
| Enclosures code (IEC529) | IP 40 for case IP 00 for terminals without back cover IP 20 for terminals with back cover |
Note: Technical Specifications and illustrations are subject to change arising out of continuous Product Development.
Powertrac Meters Pvt Ltd Head Office: 92/252, Gokhle Marg, Shipra path, Agarwal Fram, Mansarover, Jaipur, Rajasthan, India-302020. 
+91-93 1447 2389 
sales@powertracindia.comCopyright © 2023 Powertrac Meters Pvt Ltd | All Rights Reserved | Designed By : Aunicode International
